At Sunny Welding Service, we can start discussing custom steel fabrication in Melbourne with a dimensioned sketch, an existing component or a set of drawings. For an accurate quote, we need the intended dimensions, material, quantity and finish. Structural components generally require engineer-issued design information and approved fabrication details before manufacture. The better your project information, the fewer assumptions we need to make.
Quick Checklist: What to Send Your Steel Fabricator
- A drawing, sketch or photograph showing the component and how it will be used
- Overall dimensions, critical hole centres, connection points and units (usually millimetres)
- Required steel grade, section sizes or material thickness, if specified
- Quantity, including whether the job is a prototype or repeat production run
- Finish and exposure conditions, such as painted, powder-coated or galvanised
- Installation location, site-access requirements and your preferred delivery date
- The latest drawing revision, plus relevant architectural or engineering documents for structural work
If you do not have every detail yet, send what you have and identify what remains undecided. We can assess the scope of a one-off component without treating an early sketch as an approved fabrication drawing.
1. Start With a Dimensioned Sketch, CAD Drawing or Physical Sample
For a straightforward bracket, equipment support, frame or replacement part, a clear hand sketch can be a useful starting point. Show the front, side and top views where needed, then mark overall length, width and height. Include hole diameters, spacing, bends and any features that must line up with existing equipment.
For an existing component, provide photographs with a ruler or tape measure in view. A physical sample may help explain an unusual profile, but a photograph alone is rarely enough to confirm precise dimensions or fit. Let us know whether dimensions are approximate or need to be reproduced exactly.
2. Identify the Material, Thickness and Finish
The same drawing can produce very different results depending on the steel specified. Tell us whether the project requires mild or structural steel, and share any nominated grade or product designation. Include plate thickness, tube or section dimensions and any material certification requirements stipulated by your designer or purchaser.
Describe the working environment too. A component installed outdoors or exposed to moisture may need a different corrosion-protection system from an indoor shopfitting frame. Identify any surface finish, coating, colour and visible weld requirements. For custom jobs, agreeing on finishes early helps avoid changes after cutting and welding.
3. Mark Critical Fits, Holes, Welds and Tolerances
Not every dimension needs the same precision. Point out which faces, fixing holes, clearances or mating parts control the fit. If a component bolts onto an existing machine or sits between established building elements, the distance between those connection points is especially important.
Where the design requires them, supply specified tolerances, weld details, hole sizes and connection arrangements. Do not assume that a general sketch determines structural weld sizes. For load-bearing work, those details must follow the relevant engineer-approved design and project specification.
4. Understand the Difference Between Design Drawings and Shop Drawings
An architectural plan helps explain where an item belongs and what it should look like. Structural engineering drawings define the design requirements for load-bearing members and connections. Shop drawings translate the approved design into the individual pieces, dimensions and assembly details required for manufacture and erection.
The Australian Steel Institute’s guidance on steel detailing explains that shop drawings should identify member sizes, dimensions, welding, bolting and surface-treatment requirements. For structural work, clarify who is responsible for preparing, coordinating and approving these documents before fabrication begins.
Structural steelwork may also be subject to AS/NZS 5131 and project-specific documentation requirements. We recommend resolving drawing discrepancies and any required engineering review before cutting steel, rather than relying on site adjustments to solve design conflicts.
5. Include Quantity, Revision and Delivery Information
A single prototype and a repeat order of identical components can require different preparation. Tell us the total quantity and whether the first piece needs checking before the remainder is produced. Number your drawings and include revision dates so everyone works from the same version.
If your programme has a fixed installation window, identify the required date and whether the work is for workshop collection, delivery or site installation. Also note restricted access, lifting constraints or other practical considerations where relevant. These details help us scope the fabrication work and discuss a realistic project sequence.
What If You Do Not Have Formal Fabrication Drawings?
You can still contact our Thomastown workshop with your sketch, photographs, sample or project brief. We can discuss the information needed to price and fabricate a suitable non-structural custom component. For structural elements, incomplete drawings may first need clarification by your engineer or detailer before the work can be released for manufacture.
We also accept customer-supplied materials for suitable welding and fabrication jobs. When requesting a quote for supplied steel, confirm its dimensions, grade and condition, along with the work you want performed.
Common Drawing Mistakes That Delay a Quote
- No dimensions or no indication of the measurement units
- Missing steel grade, section size or thickness
- Photographs without a clear reference measurement
- Unclear hole positions, interfaces or installation clearances
- Conflicting drawing revisions or changes marked only in emails
- No distinction between approximate dimensions and critical tolerances
You do not need a complicated drawing package for every small custom part. You do need enough consistent information for us to understand what must be made and where it must fit.
Send Your Drawings to Sunny Welding Service
At Sunny Welding Service, our fabricators work with builders, manufacturers and property owners across Melbourne on one-off components, prototypes and repeat fabrication requirements. Send the available drawings or project details, tell us what is still undecided and we can discuss the next steps.
Explore our custom steel fabrication services in Melbourne or email admin@sunnyweldingservice.com to request a tailored quote.
For projects involving beams, columns or other load-bearing components, see our structural steel fabrication services in Melbourne for the broader fabrication and installation scope.
